Попробовал все тоже самое, но для SSD NVMe (тот же образ regular-kde5-rk-arm-20230313-aarch64.img.xz, также сбросил флаг boot).
Пару раз не с первого раза загрузилось с SSD NVMe. Удалось в первый раз сделать первоначальную настройку, во второй систему загрузить.
Пример лога UART, неудачной загрузки (немного сократил т.к. в сообщение не влазиет):
DDR Version V1.08 20220617
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
...
Trying to boot from MTD2
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(581130cddd...) + OK
...
## Checking optee 0x08400000 ... sha256(603cfbd25d...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 518.688 ms
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-364-g55ca4fb1c:derrick.huang
NOTICE: BL31: Built : 12:00:02, May 13 2022
...
U-Boot 2017.09-armbian (Mar 01 2023 - 16:19:19 +0300)
Model: Radxa ROCK 5B
PreSerial: 2, raw, 0xfeb50000
DRAM: 15.7 GiB
Sysmem: init
Relocation Offset: edb33000
Relocation fdt: eb9f8bb8 - eb9fecd0
CR: M/C/I
Using default environment
SF: Detected sfc_nor with page size 256 Bytes, erase size 4 KiB, total 16 MiB
Bootdev(atags): mtd 2
PartType: EFI
DM: v2
No misc partition
boot mode: None
FIT: No boot partition
** Unrecognized filesystem type **
No resource partition
No resource partition
No resource partition
Failed to load DTB, ret=-19
No find valid DTB, ret=-22
Failed to get kernel dtb, ret=-22
Unknown command 'gpio' - try 'help'
Model: Radxa ROCK 5B
CLK: (sync kernel. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
...
No misc partition
Net: No ethernet found.
Hit key to stop autoboot('CTRL+C'): 0
starting USB...
Bus usb@fc800000: USB EHCI 1.00
Bus usb@fc840000: USB OHCI 1.0
Bus usb@fc880000: USB EHCI 1.00
Bus usb@fc8c0000: USB OHCI 1.0
Bus usb@fcd00000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fc800000 for devices... 3 USB Device(s) found
scanning bus usb@fc840000 for devices... 1 USB Device(s) found
scanning bus usb@fc880000 for devices... 1 USB Device(s) found
scanning bus usb@fc8c0000 for devices... 1 USB Device(s) found
scanning bus usb@fcd00000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Device 0: unknown device
no mmc device at slot 1
no mmc device at slot 0
invalid flags type!
Device 0: Vendor: 0x1e4b Rev: SN09843 Prod: 0003567006134
Type: Hard Disk
Capacity: 488386.3 MB = 476.9 GB (1000215216 x 512)
... is now current device
Scanning nvme 0:2...
fs_devread read outside partition 7980508726312326976
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
=================begin===================
491 bytes read in 2 ms (239.3 KiB/s)
1: linux
Retrieving file: /boot/extlinux/../initrd.img
=================begin===================
7329008 bytes read in 6 ms (1.1 GiB/s)
Retrieving file: /boot/extlinux/../vmlinuz
=================begin===================
33745408 bytes read in 23 ms (1.4 GiB/s)
!!! env helper try: /boot/uEnv.txt
Retrieving file: /boot/uEnv.txt
** File not found /boot/uEnv.txt **
append: root=UUID=4f656f39-4b12-40c8-bad6-18583a6a5b88 ro console=ttyS02,1500000 console=tty0
Retrieving file: /boot/extlinux/../dtb/rockchip/rk3588-rock-5b.dtb
=================begin===================
255695 bytes read in 3 ms (81.3 MiB/s)
Fdt Ramdisk skip relocation
No misc partition
## Flattened Device Tree blob at 0x0a100000
Booting using the fdt blob at 0x0a100000
'reserved-memory' cma: addr=10000000 size=10000000
'reserved-memory' ramoops@110000: addr=110000 size=f0000
Using Device Tree in place at 000000000a100000, end 000000000a1416ce
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x3fc000000 (size: 0x2fc000000)
Adding bank: 0x3fc500000 - 0x3fff00000 (size: 0x03a00000)
Total: 7863.624 ms
Starting kernel ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
...
[ 7.982618] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 7.982644] Linux version 5.10.110-std-def-rk-alt2 (builder@localhost.localdomain) (gcc-12 (GCC) 12.1.1 20220518 (ALT Sisyphus 12.1.1-alt2), GNU ld (GNU Binutils) 2.38.20220708) #1 SMP Thu Mar 2 08:27:52 UTC 2023
[ 7.993969] Machine model: Radxa ROCK 5B
[ 8.003172] efi: UEFI not found.
[ 8.007064] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-logo@00000000': base 0x0000000000000000, size 0 MiB
[ 8.007086] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-cubic-lut@00000000': base 0x0000000000000000, size 0 MiB
...
[ 13.169913] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 405; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '08:18:26', on 'Mar 2 2023'.
[ 13.177486] Mali:
[ 13.177491] Mali device driver loaded
[ 13.184892] usb 1-1.3: new full-speed USB device number 5 using ehci-platform
[ 13.185326] ALSA device list:
DDR Version V1.08 20220617
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
...
Manufacturer ID:0xff
CH0 RX Vref:29.7%, TX Vref:21.8%,21.8%
...
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-armbian (Mar 01 2023 - 16:19:19)
Trying to boot from MMC1
Card did not respond to voltage select!
mmc_init: -95, time 13
spl: mmc init failed with error: -95
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 0
spl: mmc init failed with error: -123
Trying to boot from MTD2
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(581130cddd...) + OK
## Checking uboot 0x00200000 ... sha256(fc19f8b5dd...) + OK
## Checking fdt 0x00343ee8 ... sha256(60b3966c5c...) + OK
## Checking atf-2 0x000f0000 ... sha256(6a00298af8...) + OK
## Checking atf-3 0xff100000 ... sha256(71c3a5841b...) + OK
## Checking atf-4 0xff001000 ... sha256(2301cf73be...) + OK
## Checking optee 0x08400000 ... sha256(603cfbd25d...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 517.882 ms
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-364-g55ca4fb1c:derrick.huang
NOTICE: BL31: Built : 12:00:02, May 13 2022
INFO: timer_hp_init no valid 32k timer source, use normal mode
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: system boots from cpu-hwid-0
INFO: idle_st=0x21fff, pd_st=0x11fff9
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
INFO: hdmirx_handler: dma not on, ret
I/TC:
I/TC: OP-TEE version: 3.13.0-639-g8e053a881-dev #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #2 Mon Mar 14 09:09:01 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
U-Boot 2017.09-armbian (Mar 01 2023 - 16:19:19 +0300)
Model: Radxa ROCK 5B
PreSerial: 2, raw, 0xfeb50000
DRAM: 15.7 GiB
Sysmem: init
Relocation Offset: edb33000
Relocation fdt: eb9f8bb8 - eb9fecd0
CR: M/C/I
Using default environment
SF: Detected sfc_nor with page size 256 Bytes, erase size 4 KiB, total 16 MiB
Bootdev(atags): mtd 2
PartType: EFI
DM: v2
No misc partition
boot mode: None
FIT: No boot partition
** Unrecognized filesystem type **
No resource partition
No resource partition
No resource partition
Failed to load DTB, ret=-19
No find valid DTB, ret=-22
Failed to get kernel dtb, ret=-22
Unknown command 'gpio' - try 'help'
Model: Radxa ROCK 5B
CLK: (sync kernel. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
b0pll 816000 KHz
b1pll 816000 KHz
lpll 816000 KHz
v0pll 24000 KHz
aupll 24000 KHz
cpll 1500000 KHz
gpll 1188000 KHz
npll 24000 KHz
ppll 1100000 KHz
aclk_center_root 702000 KHz
pclk_center_root 100000 KHz
hclk_center_root 396000 KHz
aclk_center_low_root 500000 KHz
aclk_top_root 750000 KHz
pclk_top_root 100000 KHz
aclk_low_top_root 396000 KHz
No misc partition
Net: No ethernet found.
Hit key to stop autoboot('CTRL+C'): 0
starting USB...
Bus usb@fc800000: USB EHCI 1.00
Bus usb@fc840000: USB OHCI 1.0
Bus usb@fc880000: USB EHCI 1.00
Bus usb@fc8c0000: USB OHCI 1.0
Bus usb@fcd00000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fc800000 for devices... 3 USB Device(s) found
scanning bus usb@fc840000 for devices... 1 USB Device(s) found
scanning bus usb@fc880000 for devices... DDR Version V1.08 20220617
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
Manufacturer ID:0xff
CH0 RX Vref:29.7%, TX Vref:21.8%,21.8%
CH1 RX Vref:28.7%, TX Vref:20.8%,20.8%
CH2 RX Vref:28.7%, TX Vref:21.8%,19.8%
CH3 RX Vref:28.7%, TX Vref:20.8%,20.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-armbian (Mar 01 2023 - 16:19:19)
Trying to boot from MMC1
Card did not respond to voltage select!
mmc_init: -95, time 13
spl: mmc init failed with error: -95
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 0
spl: mmc init failed with error: -123
Trying to boot from MTD2
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(581130cddd...) + OK
## Checking uboot 0x00200000 ... sha256(fc19f8b5dd...) + OK
## Checking fdt 0x00343ee8 ... sha256(60b3966c5c...) + OK
## Checking atf-2 0x000f0000 ... sha256(6a00298af8...) + OK
## Checking atf-3 0xff100000 ... sha256(71c3a5841b...) + OK
## Checking atf-4 0xff001000 ... sha256(2301cf73be...) + OK
## Checking optee 0x08400000 ... sha256(603cfbd25d...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 519.89 ms
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-364-g55ca4fb1c:derrick.huang
NOTICE: BL31: Built : 12:00:02, May 13 2022
INFO: timer_hp_init no valid 32k timer source, use normal mode
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: system boots from cpu-hwid-0
INFO: idle_st=0x21fff, pd_st=0x11fff9
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
INFO: hdmirx_handler: dma not on, ret
I/TC:
I/TC: OP-TEE version: 3.13.0-639-g8e053a881-dev #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #2 Mon Mar 14 09:09:01 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
U-Boot 2017.09-armbian (Mar 01 2023 - 16:19:19 +0300)
Model: Radxa ROCK 5B
PreSerial: 2, raw, 0xfeb50000
DRAM: 15.7 GiB
Sysmem: init
Relocation Offset: edb33000
Relocation fdt: eb9f8bb8 - eb9fecd0
CR: M/C/I
Using default environment
SF: Detected sfc_nor with page size 256 Bytes, erase size 4 KiB, total 16 MiB
Bootdev(atags): mtd 2
PartType: EFI
DM: v2
No misc partition
boot mode: None
FIT: No boot partition
** Unrecognized filesystem type **
No resource partition
No resource partition
No resource partition
Failed to load DTB, ret=-19
No find valid DTB, ret=-22
Failed to get kernel dtb, ret=-22
Unknown command 'gpio' - try 'help'
Model: Radxa ROCK 5B
CLK: (sync kernel. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
b0pll 816000 KHz
b1pll 816000 KHz
lpll 816000 KHz
v0pll 24000 KHz
aupll 24000 KHz
cpll 1500000 KHz
gpll 1188000 KHz
npll 24000 KHz
ppll 1100000 KHz
aclk_center_root 702000 KHz
pclk_center_root 100000 KHz
hclk_center_root 396000 KHz
aclk_center_low_root 500000 KHz
aclk_top_root 750000 KHz
pclk_top_root 100000 KHz
aclk_low_top_root 396000 KHz
No misc partition
Net: No ethernet found.
Hit key to stop autoboot('CTRL+C'): 0
starting USB...
Bus usb@fc800000: USB EHCI 1.00
Bus usb@fc840000: USB OHCI 1.0
Bus usb@fc880000: USB EHCI 1.00
Bus usb@fc8c0000: USB OHCI 1.0
Bus usb@fcd00000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fc800000 for devices... 3 USB Device(s) found
scanning bus usb@fc840000 for devices... DDR Version V1.08 20220617
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
Manufacturer ID:0xff
CH0 RX Vref:29.7%, TX Vref:20.8%,20.8%
CH1 RX Vref:27.7%, TX Vref:21.8%,21.8%
CH2 RX Vref:28.7%, TX Vref:21.8%,20.8%
CH3 RX Vref:27.7%, TX Vref:19.8%,20.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-armbian (Mar 01 2023 - 16:19:19)
Trying to boot from MMC1
Card did not respond to voltage select!
mmc_init: -95, time 13
spl: mmc init failed with error: -95
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 0
spl: mmc init failed with error: -123
Trying to boot from MTD2
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(581130cddd...) + OK
## Checking uboot 0x00200000 ... sha256(fc19f8b5dd...) + OK
## Checking fdt 0x00343ee8 ... sha256(60b3966c5c...) + OK
## Checking atf-2 0x000f0000 ... sha256(6a00298af8...) + OK
## Checking atf-3 0xff100000 ... sha256(71c3a5841b...) + OK
## Checking atf-4 0xff001000 ... sha256(2301cf73be...) + OK
## Checking optee 0x08400000 ... sha256(603cfbd25d...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 519.55 ms
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-364-g55ca4fb1c:derrick.huang
NOTICE: BL31: Built : 12:00:02, May 13 2022
INFO: timer_hp_init no valid 32k timer source, use normal mode
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: system boots from cpu-hwid-0
INFO: idle_st=0x21fff, pd_st=0x11fff9
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
INFO: hdmirx_handler: dma not on, ret
I/TC:
I/TC: OP-TEE version: 3.13.0-639-g8e053a881-dev #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #2 Mon Mar 14 09:09:01 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
U-Boot 2017.09-armbian (Mar 01 2023 - 16:19:19 +0300)
Model: Radxa ROCK 5B
PreSerial: 2, raw, 0xfeb50000
DRAM: 15.7 GiB
Sysmem: init
Relocation Offset: edb33000
Relocation fdt: eb9f8bb8 - eb9fecd0
CR: M/C/I
Using default environment
SF: Detected sfc_nor with page size 256 Bytes, erase size 4 KiB, total 16 MiB
Bootdev(atags): mtd 2
PartType: EFI
DM: v2
No misc partition
boot mode: None
FIT: No boot partition
** Unrecognized filesystem type **
No resource partition
No resource partition
No resource partition
Failed to load DTB, ret=-19
No find valid DTB, ret=-22
Failed to get kernel dtb, ret=-22
Unknown command 'gpio' - try 'help'
Model: Radxa ROCK 5B
CLK: (sync kernel. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
b0pll 816000 KHz
b1pll 816000 KHz
lpll 816000 KHz
v0pll 24000 KHz
aupll 24000 KHz
cpll 1500000 KHz
gpll 1188000 KHz
npll 24000 KHz
ppll 1100000 KHz
aclk_center_root 702000 KHz
pclk_center_root 100000 KHz
hclk_center_root 396000 KHz
aclk_center_low_root 500000 KHz
aclk_top_root 750000 KHz
pclk_top_root 100000 KHz
aclk_low_top_root 396000 KHz
No misc partition
Net: No ethernet found.
Hit key to stop autoboot('CTRL+C'): 0
starting USB...
Bus usb@fc800000: USB EHCI 1.00
Bus usb@fc840000: USB OHCI 1.0
Bus usb@fc880000: USB EHCI 1.00
Bus usb@fc8c0000: USB OHCI 1.0
Bus usb@fcd00000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fc800000 for devices... 3 USB Device(s) found
scanning bus usb@fc840000 for devices... 1 USB Device(s) found
scanning bus usb@fc880000 for devices... 1 USB Device(s) found
scanning bus usb@fc8c0000 for devices... 1 USB Device(s) found
scanning bus usb@fcd00000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Device 0: unknown device
no mmc device at slot 1
no mmc device at slot 0
invalid flags type!
Device 0: Vendor: 0x1e4b Rev: SN09843 Prod: 0003567006134
Type: Hard Disk
Capacity: 488386.3 MB = 476.9 GB (1000215216 x 512)
... is now current device
Scanning nvme 0:2...
fs_devread read outside partition 7980508726312326976
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
fs_devread read outside partition 7994694899913690112
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
=================begin===================
491 bytes read in 2 ms (239.3 KiB/s)
1: linux
Retrieving file: /boot/extlinux/../initrd.img
=================begin===================
7329008 bytes read in 7 ms (998.5 MiB/s)
Retrieving file: /boot/extlinux/../vmlinuz
=================begin===================
33745408 bytes read in 23 ms (1.4 GiB/s)
!!! env helper try: /boot/uEnv.txt
Retrieving file: /boot/uEnv.txt
** File not found /boot/uEnv.txt **
append: root=UUID=4f656f39-4b12-40c8-bad6-18583a6a5b88 ro console=ttyS02,1500000 console=tty0
Retrieving file: /boot/extlinux/../dtb/rockchip/rk3588-rock-5b.dtb
Failed to iterate over directory boot
** File not found /boot/extlinux/../dtb/rockchip/rk3588-rock-5b.dtb **
Skipping linux for failure retrieving fdt
2: 5.10.110-std-def-rk-alt2
Retrieving file: /boot/extlinux/../initrd-5.10.110-std-def-rk-alt2.img
Failed to iterate over directory boot
** File not found /boot/extlinux/../initrd-5.10.110-std-def-rk-alt2.img **
Skipping 5.10.110-std-def-rk-alt2 for failure retrieving initrd
SCRIPT FAILED: continuing...
Failed to iterate over directory dtb
Device 2: Vendor: 0x2207 Rev: V1.00 Prod: sfc_nor
Type: Hard Disk
Capacity: 16.0 MB = 0.0 GB (32768 x 512)
... is now current device
** Unrecognized filesystem type **
Device 1:
Device 0: unknown device
No ethernet found.
missing environment variable: pxeuuid
Retrieving file: /boot/extlinux/pxelinux.cfg/00000000
No ethernet found.
Retrieving file: /boot/extlinux/pxelinux.cfg/0000000
No ethernet found.
Retrieving file: /boot/extlinux/pxelinux.cfg/000000
No ethernet found.
Retrieving file: /boot/extlinux/pxelinux.cfg/00000
No ethernet found.
Retrieving file: /boot/extlinux/pxelinux.cfg/0000
No ethernet found.
Retrieving file: /boot/extlinux/pxelinux.cfg/000
No ethernet found.
Retrieving file: /boot/extlinux/pxelinux.cfg/00
No ethernet found.
Retrieving file: /boot/extlinux/pxelinux.cfg/0
No ethernet found.
Retrieving file: /boot/extlinux/pxelinux.cfg/default-arm-rockchip
No ethernet found.
Retrieving file: /boot/extlinux/pxelinux.cfg/default-arm
No ethernet found.
Retrieving file: /boot/extlinux/pxelinux.cfg/default
No ethernet found.
Config file not found
No ethernet found.
No ethernet found.
Could not get mtd 0
## Booting FIT Image FIT: No boot partition
FIT: No fit blob
FIT: No FIT image
Could not find misc partition
Could not find uboot part
=>