Автор Тема: Cubietruck и Altlinux ARM  (Прочитано 10508 раз)

Оффлайн Merblud

  • Давно тут
  • **
  • Сообщений: 244
Re: Cubietruck и Altlinux ARM
« Ответ #30 : 24.03.2014 20:43:09 »
2 glebfm

Кстати, а SD-карточки выше 10 класса не приходилось использовать? Может быть от них какой толк, или это деньги на ветер?

Оффлайн glebfm

  • alt linux team
  • ***
  • Сообщений: 34
Re: Cubietruck и Altlinux ARM
« Ответ #31 : 24.03.2014 20:52:53 »
MicroSD конечно вносит свой отрицательный вклад в производительность (весьма ощутимый). Но все-таки не только в ней дело. В конце концов можно заменить ondemand на performance. Просто для ARM снижение частоты очень чувствуется, а тут еще A7 не блещет производительностью. Поэтому применение ondemand (если оно вообще хоть как-то в данном случае оправдано) должно быть очень хорошо отстроено.
Снижение частоты до 60, да еще и неспешное ее поднятие приводит к жутким тормозам. Но это все пока что не так важно. Может и подождать.
Думаю, всё же будет ondemand по умолчанию. И настройка через cpufreq-simple.

Лично мне больше интересно на данный момент, как добиться восстановления системного времени из энергонезависимых часов.
dmesg показывает, что драйвер для rtc стартует, но может правильно прочесть дату и время. В то же время, загрузив сразу же после этого android из nand, время отобразилось правильно. И, если мне не изменяет память, под cunian с часами тоже не было проблем.
Там в файл /etc/sysconfig/clock в самый-самый конец попала строка
HWCLOCK_SET_TIME_AT_START=falseУдалите её и перезагрузитесь.

Спасибо!

Кстати, а SD-карточки выше 10 класса не приходилось использовать? Может быть от них какой толк, или это деньги на ветер?
Не, не приходилось. Правда, практика вообще показывает, что классы — это фикция и флешки даже 10 класса очень часто ему совершенно не соответствуют.

Оффлайн glebfm

  • alt linux team
  • ***
  • Сообщений: 34
Re: Cubietruck и Altlinux ARM
« Ответ #32 : 24.03.2014 21:02:08 »
Там в файл /etc/sysconfig/clock в самый-самый конец попала строка
HWCLOCK_SET_TIME_AT_START=falseУдалите её и перезагрузитесь.

Ой. Нет, с часами что-то хитрее. Буду смотреть.

Оффлайн Merblud

  • Давно тут
  • **
  • Сообщений: 244
Re: Cubietruck и Altlinux ARM
« Ответ #33 : 25.03.2014 17:00:19 »
2 glebfm

Насчет часов вопрос снят. Не знаю, почему сразу не заработали. Но сейчас время сохраняется. И в Альтовском контрольном центре время выставляется. Так что извиняюсь, что сбил с толку.


Оффлайн Merblud

  • Давно тут
  • **
  • Сообщений: 244
Re: Cubietruck и Altlinux ARM
« Ответ #34 : 25.03.2014 20:53:26 »
Никак не могу понять, почему тормозят X под Альтом.
До Альта пробовал cubieez. Cubieez работал шустро.
А вот под Альтом двигаю окошки, так они отстают на несколько см от указателя мыши как будто на резинке.
Установил governor performance. Установил частоту в 1 ГГц. Установил одинаковое разрешение экрана как под Альтом, так и под Cubieez. В script.bin выставил одинаковую частоту (pll) и делитель для mali.
И все равно под Альтом тормоза. Уж и не знаю, что еще проверить.

Оффлайн glebfm

  • alt linux team
  • ***
  • Сообщений: 34
Re: Cubietruck и Altlinux ARM
« Ответ #35 : 26.03.2014 18:04:11 »
Никак не могу понять, почему тормозят X под Альтом.
До Альта пробовал cubieez. Cubieez работал шустро.
А вот под Альтом двигаю окошки, так они отстают на несколько см от указателя мыши как будто на резинке.
Установил governor performance. Установил частоту в 1 ГГц. Установил одинаковое разрешение экрана как под Альтом, так и под Cubieez. В script.bin выставил одинаковую частоту (pll) и делитель для mali.
И все равно под Альтом тормоза. Уж и не знаю, что еще проверить.

Проверьте, находится ли пользователь, от имени которого вы работаете в группе xgrp.
Ещё проверьте
ls -l /dev/cedar_dev /dev/disp /dev/g2d /dev/mali /dev/umpЧто они root:xgrp 660.
И посмотрите в Xorg.*.log, используется ли fbturbo.

Оффлайн Merblud

  • Давно тут
  • **
  • Сообщений: 244
Re: Cubietruck и Altlinux ARM
« Ответ #36 : 27.03.2014 09:42:27 »
Пользователь в группе xgrp состоит.
У всех устройств права crw-rw-r--.

Оффлайн Merblud

  • Давно тут
  • **
  • Сообщений: 244
Re: Cubietruck и Altlinux ARM
« Ответ #37 : 27.03.2014 09:47:48 »
Вот Xorg.log
[    33.298]
X.Org X Server 1.15.0.901 (1.15.1 RC 1)
Release Date: 2014-03-21
[    33.299] X Protocol Version 11, Revision 0
[    33.299] Build Operating System: ALT Linux 1.1.5 Server Light r5 (Collybia confluens) armv7l
[    33.299] Current Operating System: Linux localhost.localdomain 3.4.79-sun7i-alt1 #1 SMP Tue Feb 18 14:42:15 UTC 2014 armv7l
[    33.299] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 ro
[    33.300] Build Date: 24 March 2014  03:13:14PM
[    33.300] 
[    33.300] Current version of pixman: 0.32.4
[    33.300] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[    33.300] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    33.302] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Mar 26 13:02:50 2014
[    33.319] (==) Using config file: "/etc/X11/xorg.conf"
[    33.319] (==) Using config directory: "/etc/X11/xorg.conf.d"
[    33.319] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    33.336] (==) No Layout section.  Using the first Screen section.
[    33.336] (**) |-->Screen "default" (0)
[    33.336] (**) |   |-->Monitor "default"
[    33.339] (**) |   |-->Device "sunxi"
[    33.339] (==) Automatically adding devices
[    33.339] (==) Automatically enabling devices
[    33.339] (==) Automatically adding GPU devices
[    33.339] (==) FontPath set to:
catalogue:/etc/X11/fontpath.d
[    33.343] (==) ModulePath set to "/usr/lib/X11/modules"
[    33.343] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[    33.343] (II) Loader magic: 0x14bed4
[    33.343] (II) Module ABI versions:
[    33.344] X.Org ANSI C Emulation: 0.4
[    33.344] X.Org Video Driver: 15.0
[    33.344] X.Org XInput driver : 20.0
[    33.344] X.Org Server Extension : 8.0
[    33.362] (II) xfree86: Adding drm device (/dev/dri/card0)
[    33.364] (II) xfree86: Adding drm device (/dev/dri/card1)
[    33.364] Initializing built-in extension Generic Event Extension
[    33.365] Initializing built-in extension SHAPE
[    33.365] Initializing built-in extension MIT-SHM
[    33.365] Initializing built-in extension XInputExtension
[    33.365] Initializing built-in extension XTEST
[    33.365] Initializing built-in extension BIG-REQUESTS
[    33.365] Initializing built-in extension SYNC
[    33.365] Initializing built-in extension XKEYBOARD
[    33.366] Initializing built-in extension XC-MISC
[    33.366] Initializing built-in extension SECURITY
[    33.366] Initializing built-in extension XINERAMA
[    33.366] Initializing built-in extension XFIXES
[    33.366] Initializing built-in extension RENDER
[    33.366] Initializing built-in extension RANDR
[    33.366] Initializing built-in extension COMPOSITE
[    33.367] Initializing built-in extension DAMAGE
[    33.367] Initializing built-in extension MIT-SCREEN-SAVER
[    33.367] Initializing built-in extension DOUBLE-BUFFER
[    33.367] Initializing built-in extension RECORD
[    33.367] Initializing built-in extension DPMS
[    33.367] Initializing built-in extension Present
[    33.367] Initializing built-in extension DRI3
[    33.368] Initializing built-in extension X-Resource
[    33.368] Initializing built-in extension XVideo
[    33.368] Initializing built-in extension XVideo-MotionCompensation
[    33.368] Initializing built-in extension SELinux
[    33.368] Initializing built-in extension XFree86-VidModeExtension
[    33.368] Initializing built-in extension XFree86-DGA
[    33.368] Initializing built-in extension XFree86-DRI
[    33.368] Initializing built-in extension DRI2
[    33.553] (II) Executed /usr/libexec/X11/drv.d/fbturbo
[    33.553] (II) LoadModule: "glx"
[    33.610] (II) Loading /usr/lib/X11/modules/extensions/libglx.so
[    33.803] (II) Module glx: vendor="X.Org Foundation"
[    33.803] compiled for 1.15.0.901, module version = 1.0.0
[    33.804] ABI class: X.Org Server Extension, version 8.0
[    33.804] (==) AIGLX enabled
[    33.804] Loading extension GLX
[    33.804] (II) LoadModule: "fbturbo"
[    33.808] (II) Loading /usr/lib/X11/modules/drivers/fbturbo_drv.so
[    33.821] (II) Module fbturbo: vendor="X.Org Foundation"
[    33.821] compiled for 1.15.0, module version = 0.5.1
[    33.821] Module class: X.Org Video Driver
[    33.821] ABI class: X.Org Video Driver, version 15.0
[    33.822] (II) FBTURBO: driver for framebuffer: fbturbo
[    33.822] (++) using VT number 7

[    33.911] (WW) Falling back to old probe method for fbturbo
[    33.911] (II) Loading sub module "fbdevhw"
[    33.911] (II) LoadModule: "fbdevhw"
[    33.912] (II) Loading /usr/lib/X11/modules/libfbdevhw.so
[    33.915] (II) Module fbdevhw: vendor="X.Org Foundation"
[    33.915] compiled for 1.15.0.901, module version = 0.0.2
[    33.915] ABI class: X.Org Video Driver, version 15.0
[    33.916] (II) FBTURBO(0): using default device
[    33.916] (WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
[    33.917] (II) FBTURBO(0): Creating default Display subsection in Screen section
"default" for depth/fbbpp 24/32
[    33.917] (==) FBTURBO(0): Depth 24, (==) framebuffer bpp 32
[    33.917] (==) FBTURBO(0): RGB weight 888
[    33.917] (==) FBTURBO(0): Default visual is TrueColor
[    33.918] (==) FBTURBO(0): Using gamma correction (1.0, 1.0, 1.0)
[    33.918] (II) FBTURBO(0): hardware:  (video memory: 24300kB)
[    33.919] (II) FBTURBO(0): processor: ARM Cortex-A7
[    33.919] (II) FBTURBO(0): checking modes against framebuffer device...
[    33.919] (II) FBTURBO(0): checking modes against monitor...
[    33.920] (--) FBTURBO(0): Virtual size is 1920x1080 (pitch 1920)
[    33.920] (**) FBTURBO(0):  Built-in mode "current": 148.5 MHz, 67.5 kHz, 60.0 Hz
[    33.920] (II) FBTURBO(0): Modeline "current"x0.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync -csync (67.5 kHz b)
[    33.920] (==) FBTURBO(0): DPI set to (96, 96)
[    33.921] (II) Loading sub module "fb"
[    33.921] (II) LoadModule: "fb"
[    33.922] (II) Loading /usr/lib/X11/modules/libfb.so
[    33.935] (II) Module fb: vendor="X.Org Foundation"
[    33.936] compiled for 1.15.0.901, module version = 1.0.0
[    33.936] ABI class: X.Org ANSI C Emulation, version 0.4
[    33.936] (==) Depth 24 pixmap format is 32 bpp
[    33.958] (II) FBTURBO(0): using backing store heuristics
[    34.007] (II) FBTURBO(0): enabled G2D acceleration
[    34.008] (==) FBTURBO(0): Backing store enabled
[    34.016] (II) FBTURBO(0): using sunxi disp layers for X video extension
[    34.017] (II) FBTURBO(0): using hardware cursor
[    34.093] (II) Loading sub module "dri2"
[    34.093] (II) LoadModule: "dri2"
[    34.094] (II) Module "dri2" already built-in
[    34.155] (II) FBTURBO(0): enabled display controller hardware overlays for DRI2
[    34.155] (II) FBTURBO(0): Wait on SwapBuffers? enabled
[    34.155] (II) FBTURBO(0): [DRI2] Setup complete
[    34.165] (II) FBTURBO(0): [DRI2]   DRI driver: lima
[    34.165] (II) FBTURBO(0): [DRI2]   VDPAU driver: sunxi
[    34.165] (II) FBTURBO(0): using DRI2 integration for Mali GPU (UMP buffers)
[    34.165] (II) FBTURBO(0): Mali binary drivers can only accelerate EGL/GLES
[    34.165] (II) FBTURBO(0): so AIGLX/GLX is expected to fail or fallback to software
[    34.166] (==) RandR enabled
[    34.355] (II) SELinux: Disabled on system
[    34.374] (EE) AIGLX error: dlopen of /usr/lib/X11/modules/dri/lima_dri.so failed (/usr/lib/X11/modules/dri/lima_dri.so: cannot open shared object file: No such file or directory)
[    34.374] (EE) AIGLX: reverting to software rendering
[    34.622] (II) AIGLX: Loaded and initialized swrast
[    34.622] (II) GLX: Initialized DRISWRAST GL provider for screen 0
[    35.478] (II) config/udev: Adding drm device (/dev/dri/card0)
[    35.479] (II) config/udev: Adding drm device (/dev/dri/card1)
[    35.489] (II) config/udev: Adding input device axp20-supplyer (/dev/input/event0)
[    35.489] (**) axp20-supplyer: Applying InputClass "evdev keyboard catchall"
[    35.490] (II) LoadModule: "evdev"
[    35.491] (II) Loading /usr/lib/X11/modules/input/evdev_drv.so
[    35.500] (II) Module evdev: vendor="X.Org Foundation"
[    35.500] compiled for 1.15.0, module version = 2.8.2
[    35.500] Module class: X.Org XInput Driver
[    35.500] ABI class: X.Org XInput driver, version 20.0
[    35.501] (II) Using input driver 'evdev' for 'axp20-supplyer'
[    35.501] (**) axp20-supplyer: always reports core events
[    35.501] (**) evdev: axp20-supplyer: Device: "/dev/input/event0"
[    35.502] (--) evdev: axp20-supplyer: Vendor 0x1 Product 0x1
[    35.502] (--) evdev: axp20-supplyer: Found keys
[    35.502] (II) evdev: axp20-supplyer: Configuring as keyboard
[    35.502] (**) Option "config_info" "udev:/sys/devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input0/event0"
[    35.503] (II) XINPUT: Adding extended input device "axp20-supplyer" (type: KEYBOARD, id 6)
[    35.503] (**) Option "xkb_rules" "evdev"
[    35.503] (**) Option "xkb_model" "pc104"
[    35.503] (**) Option "xkb_layout" "us"
[    35.937] (II) config/udev: Adding input device HID 0430:0100 (/dev/input/event1)
[    35.937] (**) HID 0430:0100: Applying InputClass "evdev pointer catchall"
[    35.937] (II) Using input driver 'evdev' for 'HID 0430:0100'
[    35.938] (**) HID 0430:0100: always reports core events
[    35.938] (**) evdev: HID 0430:0100: Device: "/dev/input/event1"
[    35.938] (--) evdev: HID 0430:0100: Vendor 0x430 Product 0x100
[    35.938] (--) evdev: HID 0430:0100: Found 3 mouse buttons
[    35.939] (--) evdev: HID 0430:0100: Found relative axes
[    35.939] (--) evdev: HID 0430:0100: Found x and y relative axes
[    35.939] (II) evdev: HID 0430:0100: Configuring as mouse
[    35.939] (**) evdev: HID 0430:0100: YAxisMapping: buttons 4 and 5
[    35.939] (**) evdev: HID 0430:0100: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    35.940] (**) Option "config_info" "udev:/sys/devices/platform/sw-ehci.2/usb4/4-1/4-1.1/4-1.1:1.0/input/input1/event1"
[    35.940] (II) XINPUT: Adding extended input device "HID 0430:0100" (type: MOUSE, id 7)
[    35.941] (II) evdev: HID 0430:0100: initialized for relative axes.
[    35.942] (**) HID 0430:0100: (accel) keeping acceleration scheme 1
[    35.943] (**) HID 0430:0100: (accel) acceleration profile 0
[    35.943] (**) HID 0430:0100: (accel) acceleration factor: 2.000
[    35.943] (**) HID 0430:0100: (accel) acceleration threshold: 4
[    35.948] (II) config/udev: Adding input device HID 0430:0100 (/dev/input/mouse0)
[    35.949] (II) No input driver specified, ignoring this device.
[    35.949] (II) This device may have been added with another device file.
[    35.955] (II) config/udev: Adding input device HID 0430:0005 (/dev/input/event2)
[    35.955] (**) HID 0430:0005: Applying InputClass "evdev keyboard catchall"
[    35.956] (**) HID 0430:0005: Applying InputClass "keyboard"
[    35.956] (II) Using input driver 'evdev' for 'HID 0430:0005'
[    35.956] (**) HID 0430:0005: always reports core events
[    35.956] (**) evdev: HID 0430:0005: Device: "/dev/input/event2"
[    35.956] (--) evdev: HID 0430:0005: Vendor 0x430 Product 0x5
[    35.957] (--) evdev: HID 0430:0005: Found keys
[    35.957] (II) evdev: HID 0430:0005: Configuring as keyboard
[    35.957] (**) Option "config_info" "udev:/sys/devices/platform/sw-ehci.2/usb4/4-1/4-1.2/4-1.2:1.0/input/input2/event2"
[    35.957] (II) XINPUT: Adding extended input device "HID 0430:0005" (type: KEYBOARD, id 8)
[    35.957] (**) Option "xkb_rules" "evdev"
[    35.958] (**) Option "xkb_model" "pc104"
[    35.958] (**) Option "xkb_layout" "us"
[  1163.918] (II) evdev: HID 0430:0005: Close
[  1163.918] (II) UnloadModule: "evdev"
[  1163.919] (II) evdev: HID 0430:0100: Close
[  1163.926] (II) UnloadModule: "evdev"
[  1163.926] (II) evdev: axp20-supplyer: Close
[  1163.927] (II) UnloadModule: "evdev"
[  1164.210] (EE) Server terminated successfully (0). Closing log file.

Оффлайн Merblud

  • Давно тут
  • **
  • Сообщений: 244
Re: Cubietruck и Altlinux ARM
« Ответ #38 : 27.03.2014 09:50:22 »
Вот это конечно вызывает некоторые сомнения:
[    34.374] (EE) AIGLX error: dlopen of /usr/lib/X11/modules/dri/lima_dri.so failed (/usr/lib/X11/modules/dri/lima_dri.so: cannot open shared object file: No such file or directory)
[    34.374] (EE) AIGLX: reverting to software rendering
[    34.622] (II) AIGLX: Loaded and initialized swrast

Но это вроде как на 2d не может влиять.

Оффлайн Merblud

  • Давно тут
  • **
  • Сообщений: 244
Re: Cubietruck и Altlinux ARM
« Ответ #39 : 27.03.2014 09:58:42 »
Для сравнения тот же лог от Cubieez:
[   583.232]
X.Org X Server 1.12.4
Release Date: 2012-08-27
[   583.232] X Protocol Version 11, Revision 0
[   583.232] Build Operating System: Linux 3.2.0-4-mx5 armv7l Debian
[   583.232] Current Operating System: Linux cubieez 3.4.43-sun7i #1 SMP PREEMPT Thu Sep 19 21:43:14 CEST 2013 armv7l
[   583.232] Kernel command line: console=tty0 root=/dev/mmcblk0p2 rootwait loglevel=7 panic=10 macaddr=C0:0B:13:50:00:00 console=ttyS0,115200 earkyprintk=vga,ttyS0,115200 sunxi_fb_mem_reserve=32
[   583.232] Build Date: 17 April 2013  11:31:56AM
[   583.232] xorg-server 2:1.12.4-6 (Julien Cristau <jcristau@debian.org>)
[   583.233] Current version of pixman: 0.26.0
[   583.233] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[   583.233] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[   583.233] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Mar 26 17:32:20 2014
[   583.234] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[   583.236] (==) No Layout section.  Using the first Screen section.
[   583.236] (**) |-->Screen "Screen0" (0)
[   583.236] (**) |   |-->Monitor "<default monitor>"
[   583.237] (==) No device specified for screen "Screen0".
Using the first device section listed.
[   583.237] (**) |   |-->Device "Allwinner A10/A13 FBDEV"
[   583.237] (==) No monitor specified for screen "Screen0".
Using a default monitor configuration.
[   583.237] (==) Automatically adding devices
[   583.237] (==) Automatically enabling devices
[   583.238] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[   583.238] Entry deleted from font path.
[   583.238] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.
[   583.238] Entry deleted from font path.
[   583.238] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
[   583.238] Entry deleted from font path.
[   583.238] (WW) The directory "/usr/share/fonts/X11/Type1" does not exist.
[   583.238] Entry deleted from font path.
[   583.238] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.
[   583.238] Entry deleted from font path.
[   583.238] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
[   583.238] Entry deleted from font path.
[   583.238] (WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist.
[   583.238] Entry deleted from font path.
[   583.238] (==) FontPath set to:
/usr/share/fonts/X11/misc,
built-ins
[   583.238] (==) ModulePath set to "/usr/lib/xorg/modules"
[   583.238] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[   583.238] (II) Loader magic: 0xb6fafcf0
[   583.238] (II) Module ABI versions:
[   583.238] X.Org ANSI C Emulation: 0.4
[   583.239] X.Org Video Driver: 12.1
[   583.239] X.Org XInput driver : 16.0
[   583.239] X.Org Server Extension : 6.0
[   583.239] (II) LoadModule: "extmod"
[   583.240] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[   583.242] (II) Module extmod: vendor="X.Org Foundation"
[   583.242] compiled for 1.12.4, module version = 1.0.0
[   583.242] Module class: X.Org Server Extension
[   583.242] ABI class: X.Org Server Extension, version 6.0
[   583.242] (II) Loading extension SELinux
[   583.243] (II) Loading extension MIT-SCREEN-SAVER
[   583.243] (II) Loading extension XFree86-VidModeExtension
[   583.243] (II) Loading extension XFree86-DGA
[   583.243] (II) Loading extension DPMS
[   583.243] (II) Loading extension XVideo
[   583.243] (II) Loading extension XVideo-MotionCompensation
[   583.243] (II) Loading extension X-Resource
[   583.243] (II) LoadModule: "dbe"
[   583.243] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[   583.244] (II) Module dbe: vendor="X.Org Foundation"
[   583.244] compiled for 1.12.4, module version = 1.0.0
[   583.244] Module class: X.Org Server Extension
[   583.244] ABI class: X.Org Server Extension, version 6.0
[   583.244] (II) Loading extension DOUBLE-BUFFER
[   583.244] (II) LoadModule: "glx"
[   583.245] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[   583.246] (II) Module glx: vendor="X.Org Foundation"
[   583.246] compiled for 1.12.4, module version = 1.0.0
[   583.246] ABI class: X.Org Server Extension, version 6.0
[   583.246] (==) AIGLX enabled
[   583.246] (II) Loading extension GLX
[   583.246] (II) LoadModule: "record"
[   583.247] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[   583.247] (II) Module record: vendor="X.Org Foundation"
[   583.247] compiled for 1.12.4, module version = 1.13.0
[   583.247] Module class: X.Org Server Extension
[   583.248] ABI class: X.Org Server Extension, version 6.0
[   583.248] (II) Loading extension RECORD
[   583.248] (II) LoadModule: "dri"
[   583.248] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[   583.249] (II) Module dri: vendor="X.Org Foundation"
[   583.249] compiled for 1.12.4, module version = 1.0.0
[   583.249] ABI class: X.Org Server Extension, version 6.0
[   583.249] (II) Loading extension XFree86-DRI
[   583.249] (II) LoadModule: "dri2"
[   583.250] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[   583.251] (II) Module dri2: vendor="X.Org Foundation"
[   583.251] compiled for 1.12.4, module version = 1.2.0
[   583.251] ABI class: X.Org Server Extension, version 6.0
[   583.251] (II) Loading extension DRI2
[   583.251] (II) LoadModule: "sunxifb"
[   583.252] (II) Loading /usr/lib/xorg/modules/drivers/sunxifb_drv.so
[   583.256] (II) Module sunxifb: vendor="X.Org Foundation"
[   583.256] compiled for 1.12.4, module version = 0.3.1
[   583.256] Module class: X.Org Video Driver
[   583.256] ABI class: X.Org Video Driver, version 12.1
[   583.256] (II) SUNXIFB: driver for framebuffer: sunxifb
[   583.256] (++) using VT number 7

[   583.257] (WW) Falling back to old probe method for sunxifb
[   583.257] (II) Loading sub module "fbdevhw"
[   583.257] (II) LoadModule: "fbdevhw"
[   583.257] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
[   583.258] (II) Module fbdevhw: vendor="X.Org Foundation"
[   583.258] compiled for 1.12.4, module version = 0.0.2
[   583.258] ABI class: X.Org Video Driver, version 12.1
[   583.258] (II) SUNXIFB(0): using /dev/fb0
[   583.258] (WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
[   583.259] (**) SUNXIFB(0): Depth 24, (--) framebuffer bpp 32
[   583.259] (==) SUNXIFB(0): RGB weight 888
[   583.259] (==) SUNXIFB(0): Default visual is TrueColor
[   583.259] (==) SUNXIFB(0): Using gamma correction (1.0, 1.0, 1.0)
[   583.259] (II) SUNXIFB(0): hardware:  (video memory: 16200kB)
[   583.259] (**) SUNXIFB(0): Option "fbdev" "/dev/fb0"
[   583.259] (**) SUNXIFB(0): Option "AccelMethod" "G2D"
[   583.260] (II) SUNXIFB(0): processor: ARM Cortex-A7
[   583.260] (II) SUNXIFB(0): checking modes against framebuffer device...
[   583.260] (II) SUNXIFB(0): mode "1280X720" not found
[   583.260] (II) SUNXIFB(0): checking modes against monitor...
[   583.260] (--) SUNXIFB(0): Virtual size is 1920x1080 (pitch 1920)
[   583.260] (**) SUNXIFB(0):  Built-in mode "current": 148.5 MHz, 67.5 kHz, 60.0 Hz
[   583.260] (II) SUNXIFB(0): Modeline "current"x0.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync -csync (67.5 kHz b)
[   583.260] (==) SUNXIFB(0): DPI set to (96, 96)
[   583.260] (II) Loading sub module "fb"
[   583.261] (II) LoadModule: "fb"
[   583.261] (II) Loading /usr/lib/xorg/modules/libfb.so
[   583.262] (II) Module fb: vendor="X.Org Foundation"
[   583.262] compiled for 1.12.4, module version = 1.0.0
[   583.262] ABI class: X.Org ANSI C Emulation, version 0.4
[   583.262] (==) Depth 24 pixmap format is 32 bpp
[   583.264] (II) SUNXIFB(0): using backing store heuristics
[   583.281] (II) SUNXIFB(0): enabled G2D acceleration
[   583.282] (==) SUNXIFB(0): Backing store disabled
[   583.282] (EE) SUNXIFB(0): FBIOPUTCMAP: Invalid argument

[   583.295] (EE) SUNXIFB(0): FBIOPUTCMAP: Invalid argument
[   583.295] (==) SUNXIFB(0): DPMS enabled
[   583.295] (II) SUNXIFB(0): using hardware cursor
[   583.314] (II) Loading sub module "dri2"
[   583.314] (II) LoadModule: "dri2"
[   583.314] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[   583.315] (II) Module dri2: vendor="X.Org Foundation"
[   583.315] compiled for 1.12.4, module version = 1.2.0
[   583.315] ABI class: X.Org Server Extension, version 6.0
[   583.315] drmOpenDevice: node name is /dev/dri/card0
[   583.315] drmOpenDevice: open result is 10, (OK)
[   583.315] drmOpenDevice: node name is /dev/dri/card0
[   583.315] drmOpenDevice: open result is 10, (OK)
[   583.315] drmOpenDevice: node name is /dev/dri/card0
[   583.315] drmOpenDevice: open result is 10, (OK)
[   583.316] drmGetBusid returned ''
[   583.318] (II) SUNXIFB(0): enabled display controller hardware overlays for DRI2
[   583.318] (II) SUNXIFB(0): [DRI2] Setup complete
[   583.319] (II) SUNXIFB(0): [DRI2]   DRI driver: sunxi-mali
[   583.319] (II) SUNXIFB(0): using DRI2 integration for Mali GPU (UMP buffers)
[   583.319] (II) SUNXIFB(0): Mali binary drivers can only accelerate EGL/GLES
[   583.319] (II) SUNXIFB(0): so AIGLX/GLX is expected to fail or fallback to software
[   583.319] (==) RandR enabled
[   583.319] (II) Initializing built-in extension Generic Event Extension
[   583.319] (II) Initializing built-in extension SHAPE
[   583.319] (II) Initializing built-in extension MIT-SHM
[   583.319] (II) Initializing built-in extension XInputExtension
[   583.319] (II) Initializing built-in extension XTEST
[   583.319] (II) Initializing built-in extension BIG-REQUESTS
[   583.319] (II) Initializing built-in extension SYNC
[   583.319] (II) Initializing built-in extension XKEYBOARD
[   583.319] (II) Initializing built-in extension XC-MISC
[   583.319] (II) Initializing built-in extension SECURITY
[   583.319] (II) Initializing built-in extension XINERAMA
[   583.319] (II) Initializing built-in extension XFIXES
[   583.319] (II) Initializing built-in extension RENDER
[   583.319] (II) Initializing built-in extension RANDR
[   583.320] (II) Initializing built-in extension COMPOSITE
[   583.320] (II) Initializing built-in extension DAMAGE
[   583.321] (II) SELinux: Disabled on system
[   583.365] (EE) AIGLX error: dlopen of /usr/lib/arm-linux-gnueabihf/dri/sunxi-mali_dri.so failed (/usr/lib/arm-linux-gnueabihf/dri/sunxi-mali_dri.so: cannot open shared object file: No such file or directory)
[   583.366] (EE) AIGLX: reverting to software rendering
[   583.366] (II) AIGLX: Screen 0 is not DRI capable
[   583.378] (II) AIGLX: Loaded and initialized swrast
[   583.378] (II) GLX: Initialized DRISWRAST GL provider for screen 0
[   583.557] (II) config/udev: Adding input device axp20-supplyer (/dev/input/event0)
[   583.557] (**) axp20-supplyer: Applying InputClass "evdev keyboard catchall"
[   583.557] (II) LoadModule: "evdev"
[   583.558] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[   583.559] (II) Module evdev: vendor="X.Org Foundation"
[   583.559] compiled for 1.12.1, module version = 2.7.0
[   583.559] Module class: X.Org XInput Driver
[   583.559] ABI class: X.Org XInput driver, version 16.0
[   583.559] (II) Using input driver 'evdev' for 'axp20-supplyer'
[   583.559] (**) axp20-supplyer: always reports core events
[   583.559] (**) evdev: axp20-supplyer: Device: "/dev/input/event0"
[   583.559] (--) evdev: axp20-supplyer: Vendor 0x1 Product 0x1
[   583.559] (--) evdev: axp20-supplyer: Found keys
[   583.559] (II) evdev: axp20-supplyer: Configuring as keyboard
[   583.560] (**) Option "config_info" "udev:/sys/devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input0/event0"
[   583.560] (II) XINPUT: Adding extended input device "axp20-supplyer" (type: KEYBOARD, id 6)
[   583.560] (**) Option "xkb_rules" "evdev"
[   583.560] (**) Option "xkb_model" "pc105"
[   583.560] (**) Option "xkb_layout" "es"
[   583.560] (**) Option "xkb_variant" "cat"
[   583.666] (II) config/udev: Adding input device HID 0430:0100 (/dev/input/event1)
[   583.666] (**) HID 0430:0100: Applying InputClass "evdev pointer catchall"
[   583.666] (II) Using input driver 'evdev' for 'HID 0430:0100'
[   583.666] (**) HID 0430:0100: always reports core events
[   583.666] (**) evdev: HID 0430:0100: Device: "/dev/input/event1"
[   583.667] (--) evdev: HID 0430:0100: Vendor 0x430 Product 0x100
[   583.667] (--) evdev: HID 0430:0100: Found 3 mouse buttons
[   583.667] (--) evdev: HID 0430:0100: Found relative axes
[   583.667] (--) evdev: HID 0430:0100: Found x and y relative axes
[   583.667] (II) evdev: HID 0430:0100: Configuring as mouse
[   583.667] (**) evdev: HID 0430:0100: YAxisMapping: buttons 4 and 5
[   583.667] (**) evdev: HID 0430:0100: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[   583.667] (**) Option "config_info" "udev:/sys/devices/platform/sw-ehci.2/usb3/3-1/3-1.1/3-1.1:1.0/input/input1/event1"
[   583.667] (II) XINPUT: Adding extended input device "HID 0430:0100" (type: MOUSE, id 7)
[   583.667] (II) evdev: HID 0430:0100: initialized for relative axes.
[   583.668] (**) HID 0430:0100: (accel) keeping acceleration scheme 1
[   583.668] (**) HID 0430:0100: (accel) acceleration profile 0
[   583.668] (**) HID 0430:0100: (accel) acceleration factor: 2.000
[   583.668] (**) HID 0430:0100: (accel) acceleration threshold: 4
[   583.670] (II) config/udev: Adding input device HID 0430:0100 (/dev/input/mouse0)
[   583.670] (II) No input driver specified, ignoring this device.
[   583.670] (II) This device may have been added with another device file.
[   583.672] (II) config/udev: Adding input device HID 0430:0005 (/dev/input/event2)
[   583.672] (**) HID 0430:0005: Applying InputClass "evdev keyboard catchall"
[   583.672] (II) Using input driver 'evdev' for 'HID 0430:0005'
[   583.673] (**) HID 0430:0005: always reports core events
[   583.673] (**) evdev: HID 0430:0005: Device: "/dev/input/event2"
[   583.673] (--) evdev: HID 0430:0005: Vendor 0x430 Product 0x5
[   583.673] (--) evdev: HID 0430:0005: Found keys
[   583.673] (II) evdev: HID 0430:0005: Configuring as keyboard
[   583.673] (**) Option "config_info" "udev:/sys/devices/platform/sw-ehci.2/usb3/3-1/3-1.2/3-1.2:1.0/input/input2/event2"
[   583.673] (II) XINPUT: Adding extended input device "HID 0430:0005" (type: KEYBOARD, id 8)
[   583.673] (**) Option "xkb_rules" "evdev"
[   583.673] (**) Option "xkb_model" "pc105"
[   583.673] (**) Option "xkb_layout" "es"
[   583.673] (**) Option "xkb_variant" "cat"
[  1984.362] (EE) SUNXIFB(0): FBIOPUTCMAP: Invalid argument

Оффлайн glebfm

  • alt linux team
  • ***
  • Сообщений: 34
Re: Cubietruck и Altlinux ARM
« Ответ #40 : 27.03.2014 14:17:48 »
Пользователь в группе xgrp состоит.
У всех устройств права crw-rw-r--.

Но это 664. Должно быть crw-rw---- (660) и группа xgrp. Просто, там есть udev-ное правило, в котором явно проставляются права -- /etc/udev/rules.d/69-mali-gpu.rules. 664, по идее, просто неоткуда появиться!

Оффлайн Merblud

  • Давно тут
  • **
  • Сообщений: 244
Re: Cubietruck и Altlinux ARM
« Ответ #41 : 27.03.2014 16:24:09 »
Пользователь в группе xgrp состоит.
У всех устройств права crw-rw-r--.

Но это 664. Должно быть crw-rw---- (660) и группа xgrp. Просто, там есть udev-ное правило, в котором явно проставляются права -- /etc/udev/rules.d/69-mali-gpu.rules. 664, по идее, просто неоткуда появиться!

Это я просто ошибся. Смотрю на CB, а в форум пишу на другом компе. Там crw-rw---- (660) и группа xgrp.
А у вас это нормально работает?

Оффлайн glebfm

  • alt linux team
  • ***
  • Сообщений: 34
Re: Cubietruck и Altlinux ARM
« Ответ #42 : 27.03.2014 17:01:53 »
А у вас это нормально работает?
Да! В том и дело, что у меня всё нормально выглядит. У меня были проблемы с тормозящими окошками, когда загружался модуль fbdev, вместо fbturbo, но в вашем случае что-то другое.

Оффлайн glebfm

  • alt linux team
  • ***
  • Сообщений: 34
Re: Cubietruck и Altlinux ARM
« Ответ #43 : 28.03.2014 13:09:13 »
« Последнее редактирование: 28.03.2014 13:10:53 от glebfm »

Оффлайн Merblud

  • Давно тут
  • **
  • Сообщений: 244
Re: Cubietruck и Altlinux ARM
« Ответ #44 : 28.03.2014 14:39:31 »
Что там новенького?