Спасибо! Но у меня уже всё установлено. Требуется определить адрес моего устройства:
[root@localhost ~]# upsmon
Network UPS Tools upsmon 2.0.5
Using power down flag file /etc/killpower
Fatal error: insufficient power configured!
Sum of power values........: 0
Minimum value (MINSUPPLIES): 1
Edit your upsmon.conf and change the values.
[root@localhost ~]#
[root@localhost ~]# dmesg | grep -A18 BNT--???AP
usb 4-2: Product: UPS BNT--???AP FW4.A6
usb 4-2: Manufacturer: POWERCOM Co.,Ltd
usb 4-2: SerialNumber: 4A6-0000-0001
usb 4-3: new low speed USB device using ohci_hcd and address 3
usb 4-3: configuration #1 chosen from 1 choice
usb 4-3: New USB device found, idVendor=0518, idProduct=0005
usb 4-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-3: Product: USB Advance Mouse
usb 5-3: new full speed USB device using ohci_hcd and address 2
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e24e090000241d]
usb 5-3: configuration #1 chosen from 1 choice
usb 5-3: New USB device found, idVendor=1019, idProduct=0c55
usb 5-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-3: Product: USB Storage Device
usb 5-3: Manufacturer: Generic
usb 5-3: SerialNumber: 20020509145305401
usbcore: registered new interface driver hiddev
hiddev96hidraw0: USB HID v1.00 Device [POWERCOM Co.,Ltd UPS BNT--???AP FW4.A6 ] on usb-0000:00:12.1-2
input: USB Advance Mouse as /devices/pci0000:00/0000:00:12.1/usb4/4-3/4-3:1.0/input/input6
input,hidraw1: USB HID v1.10 Mouse [USB Advance Mouse] on usb-0000:00:12.1-3
input: USB Advance Mouse as /devices/pci0000:00/0000:00:12.1/usb4/4-3/4-3:1.1/input/input7
input,hidraw2: USB HID v1.10 Keyboard [USB Advance Mouse] on usb-0000:00:12.1-3
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
usbcore: registered new interface driver libusual
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
Adding 3020212k swap on /dev/sda2. Priority:-1 extents:1 across:3020212k
EXT3 FS on sda6, internal journal
scsi 4:0:0:0: Direct-Access IC USB Storage-CFC 301b PQ: 0 ANSI: 0 CCS
sd 4:0:0:0: [sdb] Attached SCSI removable disk
sd 4:0:0:0: Attached scsi generic sg2 type 0
[root@localhost ~]#
Как адрес найти? (подключён по юсб)