Huawei MTS 827F модем

[Владимир Кальметьев]

Соединение с сетью устанавливается.Как разрешить использование этого соединения в системе?

Код: [Выделить]

[vladimir@E-N-TE69CX ~]$ lspci
00:00.0 Host bridge: Intel Corporation 3rd Gen Core processor DRAM Controller (rev 09)
00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04)
00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04)
00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04)
00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4)
00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4)
00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04)
00:1f.0 ISA bridge: Intel Corporation 7 Series Chipset Family LPC Controller (rev 04)
00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04)
00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04)
02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM57786 Gigabit Ethernet PCIe (rev 01)
02:00.1 SD Host controller: Broadcom Corporation BCM57765/57785 SDXC/MMC Card Reader (rev 01)
03:00.0 Network controller: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter (rev 01)
[vladimir@E-N-TE69CX ~]$ lsusb
Bus 001 Device 002: ID 279e:024e 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 005: ID 04ca:300b Lite-On Technology Corp.
Bus 003 Device 004: ID 04f2:b3f6 Chicony Electronics Co., Ltd
Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 003: ID 12d1:1506 Huawei Technologies Co., Ltd. Modem/Networkcard
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
[vladimir@E-N-TE69CX ~]$
    В центре управления в ethernet интерфейсах соединение wwp0s29u1u3i2 Huawei Technologies Co., Ltd. Modem/Networkcard провод отсоединён Как запустить?Использую Simply Linuux 7.0.4 x86_64.

[ruslandh]

Не понял - у вас модем на USB или на pci?

[ruslandh]

Что за модель модема?

Что значит устанавливается, что значит разрешить?

[Владимир Кальметьев]

Это USB модем от оператора МТС. Программы Etecnet и NetworkManager управлять соединением модема могут,устанавливается соединение с сетью МТС а браузер использовать его не может так как в центре управления системой в Ethernet интерфейсах оно не соединено.

[Skull]

Это USB модем от оператора МТС. Программы Etecnet и NetworkManager управлять соединением модема могут,устанавливается соединение с сетью МТС а браузер использовать его не может так как в центре управления системой в Ethernet интерфейсах оно не соединено.

http://www.altlinux.org/USB-3G

[ruslandh]

Дайте команду

Код: [Выделить]

ip l(последняя буква - маленькая латинская "л")
после создания соединения.

[Владимир Кальметьев]

Вот что пишет

Код: [Выделить]

[vladimir@E-N-TE69CX ~]$ ip l
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT qlen 1000
    link/ether 20:1a:06:b9:37:e0 brd ff:ff:ff:ff:ff:ff
3: wlp3s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DORMANT qlen 1000
    link/ether 40:f0:2f:86:70:23 brd ff:ff:ff:ff:ff:ff
4: wwp0s29u1u3i2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN mode DEFAULT qlen 1000
    link/ether 00:1e:10:1f:00:00 brd ff:ff:ff:ff:ff:ff
[vladimir@E-N-TE69CX ~]$




[Владимир Кальметьев]

Вот ещё что сделал

Код: [Выделить]

[vladimir@E-N-TE69CX ~]$ ifconfig
enp2s0f0  Link encap:Ethernet  HWaddr 20:1A:06:B9:37:E0 
          inet addr:192.168.1.2  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::221a:6ff:feb9:37e0/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:344 errors:0 dropped:0 overruns:0 frame:0
          TX packets:473 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:213103 (208.1 KiB)  TX bytes:72308 (70.6 KiB)
          Interrupt:16

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:233 errors:0 dropped:0 overruns:0 frame:0
          TX packets:233 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:20531 (20.0 KiB)  TX bytes:20531 (20.0 KiB)

wlp3s0    Link encap:Ethernet  HWaddr 40:F0:2F:86:70:23 
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

wwp0s29u1u3i2 Link encap:Ethernet  HWaddr 00:1E:10:1F:00:00 
          inet addr:10.105.246.53  Bcast:10.105.246.55  Mask:255.255.255.252
          inet6 addr: fe80::21e:10ff:fe1f:0/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:3 errors:0 dropped:0 overruns:0 frame:0
          TX packets:22 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:914 (914.0 b)  TX bytes:151273 (147.7 KiB)

[vladimir@E-N-TE69CX ~]$


[ruslandh]

Осталось понять какой интерфейс относится к вашему модему :)

[ruslandh]

Скорей всего один из этих :

3: wlp3s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DORMANT qlen 1000
4: wwp0s29u1u3i2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN mode DEFAULT qlen 1000

[Владимир Кальметьев]

Интерфейс №4 относится к модему а №3 к WiFi карте pci. Это 4g 3g 2g то есеть 4g 3g EDGE GPRS универсальный модем.

[Владимир Кальметьев]

Вот ещё что интересно

Код: [Выделить]

[  298.734342] usb 1-1: USB disconnect, device number 2
[  298.] sd 4:0:0:1: [sdb] Synchronizing SCSI cache
[  298.737751] sd 4:0:0:1: [sdb] 
[  298.737756] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[  315.03506] usb 1-1: new high-speed USB device number 4 using xhci_hcd
[  315.200639] usb-storage 1-1:1.0: USB Mass Storage device detected
[  315.202973] scsi5 : usb-storage 1-1:1.0
[  316.196720] usb 1-1: USB disconnect, device number 4
[  316.653560] usb 1-1: new high-speed USB device number 5 using xhci_hcd
[  316.820584] usb-storage 1-1:1.3: USB Mass Storage device detected
[  316.820837] scsi6 : usb-storage 1-1:1.3
[  316.821263] usb-storage 1-1:1.4: USB Mass Storage device detected
[  316.822446] scsi7 : usb-storage 1-1:1.4
[  316.987998] usbcore: registered new interface driver usbserial
[  316.988018] usbcore: registered new interface driver usbserial_generic
[  316.988031] usbserial: USB Serial support registered for generic
[  317.047188] usbcore: registered new interface driver option
[  317.047215] usbserial: USB Serial support registered for GSM modem (1-port)
[  317.047414] option 1-1:1.0: GSM modem (1-port) converter detected
[  317.047762] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[  317.047794] option 1-1:1.1: GSM modem (1-port) converter detected
[  317.047874] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[  317.056015] usbcore: registered new interface driver cdc_ncm
[  317.071745] usbcore: registered new interface driver cdc_wdm
[  317.076920] huawei_cdc_ncm 1-1:1.2: MAC-Address: 00:1e:10:1f:00:00
[  317.077209] huawei_cdc_ncm 1-1:1.2: cdc-wdm0: USB WDM device
[  317.077426] huawei_cdc_ncm 1-1:1.2 wwan0: register 'huawei_cdc_ncm' at usb-0000:00:14.0-1, Huawei CDC NCM device, 00:1e:10:1f:00:00
[  317.077452] usbcore: registered new interface driver huawei_cdc_ncm
[  317.127675] systemd-udevd[3148]: renamed network interface wwan0 to wwp0s20u1i2
[  317.822604] scsi 6:0:0:0: CD-ROM            Mass     Storage          2.31 PQ: 0 ANSI: 2
[  317.823659] sr1: scsi-1 drive
[  317.823960] sr 6:0:0:0: Attached scsi CD-ROM sr1
[  317.824582] scsi 7:0:0:0: Direct-Access     TF CARD  Storage          2.31 PQ: 0 ANSI: 2
[  317.825566] sd 7:0:0:0: [sdb] 62676992 512-byte logical blocks: (32.0 GB/29.8 GiB)
[  317.825759] sd 7:0:0:0: [sdb] Write Protect is off
[  317.825767] sd 7:0:0:0: [sdb] Mode Sense: 0f 00 00 00
[  317.825946] sd 7:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  317.828901]  sdb: sdb1
[  317.830029] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[  318.145269] FAT-fs (sdb1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[  318.185203] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[  319.781980] ISO 9660 Extensions: Microsoft Joliet Level 1
[  319.782251] ISOFS: changing to secondary root
[  355.385838] wlp3s0: deauthenticating from 28:c6:8e:3d:66:3c by local choice (reason=3)
[  355.395517] cfg80211: Calling CRDA to update world regulatory domain
[  789.386398] huawei_cdc_ncm 1-1:1.2: nonzero urb status received: -71
[  789.386407] huawei_cdc_ncm 1-1:1.2: wdm_int_callback - 0 bytes
[  789.386615] usb 1-1: USB disconnect, device number 5
[  789.386636] option1 ttyUSB1: usb_wwan_indat_callback: resubmit read urb failed. (-19)
[  789.386671] option1 ttyUSB1: usb_wwan_indat_callback: resubmit read urb failed. (-19)
[  789.386710] option1 ttyUSB1: usb_wwan_indat_callback: resubmit read urb failed. (-19)
[  789.386752] option1 ttyUSB1: usb_wwan_indat_callback: resubmit read urb failed. (-19)
[  789.386904] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[  789.386934] option 1-1:1.0: device disconnected
[  789.388390] huawei_cdc_ncm 1-1:1.2: nonzero urb status received: -71
[  789.388395] huawei_cdc_ncm 1-1:1.2: wdm_int_callback - 0 bytes
[  789.388400] huawei_cdc_ncm 1-1:1.2: wdm_int_callback - usb_submit_urb failed with result -19
[  789.390674] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[  789.390690] option 1-1:1.1: device disconnected
[  789.390785] huawei_cdc_ncm 1-1:1.2 wwp0s20u1i2: unregister 'huawei_cdc_ncm' usb-0000:00:14.0-1, Huawei CDC NCM device
[  789.413925] sd 7:0:0:0: [sdb] Synchronizing SCSI cache
[  789.413979] sd 7:0:0:0: [sdb] 
[  789.413982] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[  804.374894] usb 1-1: new high-speed USB device number 6 using xhci_hcd
[  804.540356] usb-storage 1-1:1.0: USB Mass Storage device detected
[  804.542339] scsi8 : usb-storage 1-1:1.0
[  805.114859] usb 1-1: USB disconnect, device number 6
[  805.576503] usb 1-1: new high-speed USB device number 7 using xhci_hcd
[  805.742761] option 1-1:1.0: GSM modem (1-port) converter detected
[  805.742940] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[  805.743087] option 1-1:1.1: GSM modem (1-port) converter detected
[  805.743193] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
[  805.745474] huawei_cdc_ncm 1-1:1.2: MAC-Address: 00:1e:10:1f:00:00
[  805.745554] huawei_cdc_ncm 1-1:1.2: cdc-wdm0: USB WDM device
[  805.745806] huawei_cdc_ncm 1-1:1.2 wwan0: register 'huawei_cdc_ncm' at usb-0000:00:14.0-1, Huawei CDC NCM device, 00:1e:10:1f:00:00
[  805.746211] usb-storage 1-1:1.3: USB Mass Storage device detected
[  805.750931] scsi9 : usb-storage 1-1:1.3
[  805.751267] usb-storage 1-1:1.4: USB Mass Storage device detected
[  805.752969] scsi10 : usb-storage 1-1:1.4
[  805.821192] systemd-udevd[3761]: renamed network interface wwan0 to wwp0s20u1i2
[  806.752667] scsi 9:0:0:0: CD-ROM            Mass     Storage          2.31 PQ: 0 ANSI: 2
[  806.755473] scsi 10:0:0:0: Direct-Access     TF CARD  Storage          2.31 PQ: 0 ANSI: 2
[  806.755877] sr1: scsi-1 drive
[  806.756115] sr 9:0:0:0: Attached scsi CD-ROM sr1
[  806.756330] sd 10:0:0:0: [sdb] 62676992 512-byte logical blocks: (32.0 GB/29.8 GiB)
[  806.756524] sd 10:0:0:0: [sdb] Write Protect is off
[  806.756530] sd 10:0:0:0: [sdb] Mode Sense: 0f 00 00 00
[  806.756749] sd 10:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  806.759592]  sdb: sdb1
[  806.760636] sd 10:0:0:0: [sdb] Attached SCSI removable disk
[  808.274848] ISO 9660 Extensions: Microsoft Joliet Level 1
[  808.275057] ISOFS: changing to secondary root
[ 1142.392663] tg3 0000:02:00.0 enp2s0f0: Link is down
[ 1149.647151] usb 1-1: USB disconnect, device number 7
[ 1149.647471] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 1149.647500] option 1-1:1.0: device disconnected
[ 1149.648346] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 1149.648368] option 1-1:1.1: device disconnected
[ 1149.648465] huawei_cdc_ncm 1-1:1.2 wwp0s20u1i2: unregister 'huawei_cdc_ncm' usb-0000:00:14.0-1, Huawei CDC NCM device
[ 1149.674610] sd 10:0:0:0: [sdb] Synchronizing SCSI cache
[ 1149.674664] sd 10:0:0:0: [sdb] 
[ 1149.674668] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 1169.383338] usb 1-1: new high-speed USB device number 8 using xhci_hcd
[ 1169.510705] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 1169.512316] scsi11 : usb-storage 1-1:1.0
[ 1170.141168] usb 1-1: USB disconnect, device number 8
[ 1170.568570] usb 1-1: new high-speed USB device number 9 using xhci_hcd
[ 1170.697038] option 1-1:1.0: GSM modem (1-port) converter detected
[ 1170.697169] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 1170.697318] option 1-1:1.1: GSM modem (1-port) converter detected
[ 1170.697453] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
[ 1170.699720] huawei_cdc_ncm 1-1:1.2: MAC-Address: 00:1e:10:1f:00:00
[ 1170.700724] huawei_cdc_ncm 1-1:1.2: cdc-wdm0: USB WDM device
[ 1170.700972] huawei_cdc_ncm 1-1:1.2 wwan0: register 'huawei_cdc_ncm' at usb-0000:00:14.0-1, Huawei CDC NCM device, 00:1e:10:1f:00:00
[ 1170.701556] usb-storage 1-1:1.3: USB Mass Storage device detected
[ 1170.701681] scsi12 : usb-storage 1-1:1.3
[ 1170.701989] usb-storage 1-1:1.4: USB Mass Storage device detected
[ 1170.702091] scsi13 : usb-storage 1-1:1.4
[ 1170.755426] systemd-udevd[4027]: renamed network interface wwan0 to wwp0s20u1i2
[vladimir@E-N-TE69CX ~]$
   Код длинный не смог весь вставить.

[ksa]

 Код длинный не смог весь вставить.

По частям вставляйте.

[ruslandh]

У меня похожий модем, но под Мегафон, заработал только после того, как я для себя пересобрал новую версию usb-modeswitch.
Может и у вас такая проблема.

[ruslandh]

Не - сейчас посмотрел, в репозитории уже нужная версия есть.
Так-что обновляйте, если ещё не обновили дистрибутив до самой новой версии и всё должно заработать.